Категории

Производители

ОСЦИЛОСКОП TEKTRONIX 465

ОСЦИЛОСКОП TEKTRONIX 465

двуканален 100MHz осцилоскоп Tektronix 465 с вграден мултимер DM44

състояние: използван, работещ, 1 година гаранция

Tektronix 465 Dual-Trace 100 MHz Oscilloscope

  • Brand: Tektronix
  • Model: 465B
  • Type: Analog
  • Bandwidth: 100 MHz

Vertical System

  • Rise Time: 3.5 ns

Time Base System

  • Time Base Range: 20 ns/div to 0.5 s/div
  • Time Base Accuracy ±2%

Display

  • Display Size: 5.12 inch


Повече информация

Намалена цена!
760,00 лв с ДДС

950,00 лв с ДДС

(цената е намалена само онлайн с 20 %)

8585

30 други артикули от същата категория:

Tektronix 465 Oscilloscopes Specifications


VERTICAL DEFLECTION (2 IDENTICAL CHANNELS)
Bandwidth* and Rise
Time (at all deflection
factors from 50 Ω 
Terminated source)
  -15°C to +40°C+40°C to +55°C
  Dc to 100 MHz, 3.5 ns85 MHz, 4.1 ns
*Measured at -3 dB, Bandwidth may be limited to approx 20 MHz by bandwidth limit switch.
Lower -3 dB point, ac coupling 1X probe: 10 Hz or less. 10X probe: 1 Hz or less.
Deflection Factor at BW5 mV/div to 5 V/di
1-2-5 sequence, accurate ± 3%. Uncalibrated, continuously variable between steps and to at least 12.5 V/div (465/475) to at least 25 V/div (475A).  In cascade mode sensitivity is approx 1 mV/div ; approx 400 µV/div (475); and approx 2.5 mV/div (475A).  Cascaded bandwidth is at least 50 MHz  when signal out is terminated in 50 Ω.
Display ModesCh 1; Ch 2 (normal and inverted), alternate, chopped (465-approx 250 kHz rate, 475/475A-approx 1 MHz rate), added; X-Y (Ch 1-X, Ch 2-Y)
CMRRCommon-mode rejection ratio at least 20 dB at 20 MHz (50 MHz for 475/475A) for common-mode signals of 6 div or less
Automatic Scale FactorProbe tip deflection factors for 1X or 10X coded probes are automatically indicated by two readout lights behind the knob skirts.  All lights are off when the channel is not displayed.   Ground reference display selectable at probe (when dc coupled).
Input R and C1 MΩ  ± 2% paralleled by approx 20 pF.
Max Input VoltageDc Coupled250 V (dc + peak ac)
500 V (p-p ac at 1 kHz or less)
Ac Coupled500 V (dc + peak ac)
500 V (p-p ac at 1 kHz or less)
Delay LinePermits viewing leading edge of displayed waveform
Probe Power (475/475A only)Connectors provide correct voltages for two optional P6201 FET Probes
HORIZONTAL DEFLECTION
Time Base A0.05 µs/div to 0.5 s/div (1-2-5 sequence). X10 mag extends max sweep rate to 5 ns/div.
Time Base B0.05 µs/div to 50 ms/div (1-2-5 sequence).  X10 mag extends max sweep rate to 5 ns/div.
Variable Time ControlTime Base A provides continuously variable uncalibrated sweep rates between steps and to at least 1.25 s/div.  Warning light indicates uncalibrated setting.
Time Base A and
B Accuracy, full 10 cm
Unmagnified+20°C to +30°C-15°C to +55°C
± 2%± 3%
Magnified± 3%± 4%
Horizontal Display ModesA, mixed sweep, A intensified, B delayed.  B ends A for increased intensity in the delayed mode.
Calibrated Mixed SweepDisplays A sweep for period determined by delay-time position control, then displays B sweep for remainder of horizontal sweep.
CALIBRATED SWEEP DELAY
Delay Time Range 0.2 to X10 delay time/div settings of 200/ns to 0.5 s (minimum delay time is 200 ns).
Differential Time Measurement AccuracyDelay Time Setting+15°C to 35°C
Over one or more major dial divisions± 1%
Less than one major dial division± 0.01 major dial division
Jitter1 part or less in 50,000 (0.002%) of 10X the A sweep time/div setting. 1 part in 20,000 when operating from 50 Hz line.
TRIGGERING A AND B
A Trigger ModesNormal (sweep runs when triggered).  Automatic (sweep free-runs in the absence of a triggering signal and for signals below 30 Hz).  Single sweep (sweep runs one time on the first triggering event after the reset selector is pressed).  Lights indicate when sweep is triggered and when single sweep is ready.
A Trigger HoldoffAdjustable control permits a stable presentation of repetitive complex waveforms.
B Trigger ModesB runs after delay time (starts automatically at the end of delay time) and B triggerable after delay time (runs when triggered).  The B (delayed) sweep runs once, in each of these modes, following the A sweep delay time.
Time Base A and B Sensitivity and Coupling
  To 25 MHzAt 100 MHz    
DCInternal
 
0.3 div deflection1.5 div deflection    
External50 mV150 mV    
External +10500 mV1.5 V    
AcRequirements increase below 60 Hz
Ac Lf RejectRequirements increase below 50 kHz
Ac Hf RejectRequirements increase below 60 Hz and above 50 kHz
465 Jitter0.5 ns or less at 100 MHz and 5 ns/div
A Trigger ViewA spring-loaded pushbutton overrides other vertical controls and displays the external signal used for A sweep triggering.  This provides quick verification of the signal and time comparison between a vertical signal and their trigger signal.
Level and SlopeInternal, permits selection of triggering at any point on the positive or negative slope of the displayed waveform.  Level adjustment through at least ± 2 V in external, through at least ± 20 V in external divided by 10.
A SourcesNorm, Ch 1, Ch 2, line, external, and external divided by 10
B SourcesStarts after delay, norm, Ch 1, Ch 2, and external
External InputsR and C approx 1 MΩ  paralleled by approx 20 pF. 250 V (dc + peak ac) max input.
X-Y OPERATION
Full-sensitivity X-Y (Ch1 Horiz, Ch2 Vert)5 mV/div to 5 V/div, accurate ± 4%.  Bandwidth is dc to at least 4 MHz.  Phase difference between amplifiers is 3° or less from dc to 50 kHz.
DISPLAY
CRT8 X 10 cm display. Horizontal and vertical centerlines further marked in 0.2 cm increments.  P31 phosphor standard; P11 option.  18 kV accelerating potential.
Graticuleinternal, nonparallax; variable edge lighting; markings for measurement of rise time
Beam FinderCompresses trace to within graticule area for ease in determining the location of an offscreen signal.  A pre-set intensity level provides a constant brightness.
Z-Axis InputDc coupled, positive-going signal decreases intensity; 5 V p-p signal causes noticeable modulation at normal intensity; dc to 50 MHz.
ENVIRONMENTAL CAPABILITIES
Ambient TemperatureOperating: -15°C to +55°C.
Nonoperating: -55°C to +75°C.  Filtered forced air ventilation is provided.
AltitudeOperating: to 15,000 ft; max allowable ambient temperature decreased by 1°C/1000 ft from 5000 to 15,000 ft.   
Nonoperating: to 50,000 ft.
VibrationOperating: 15 minutes along each of the three axes, .06 cm (0.025 in) p-p displacement (4 g's at 55 Hz) 10 to 55 to 10 Hz in 1 minute cycles.
HumidityOperating and nonoperating: 5 cycles (120 hours) to 95% relative humidity referenced to MIL-E-16400F (par 4.5.9 through 4.5.9.5.1, class 4).
ShockOperating and nonoperating: 30 g's 1/2 sine, 11 ms duration, 2 shocks per axis in each direction for a total of 12 shocks.
OTHER CHARACTERISTICS
Amplitude CalibratorOutput Voltage0.3 V1%
0°C to +40°C
Output Current30 mA2%
+20°C to +30°C
FrequencyApprox 1 kHz 
Vertical Signal Output (465)Ch 1 vertical signal is dc to at least 50 MHz (-3 dB), and approx 25 mV/div terminated into 50 Ω, and approx 50 mV/div terminated into 1 MW.  (475/475A) Ch 2 vertical signal is dc to at least 50 MHz (-3 dB), and approx 10 mV/div terminated into 50 Ω, and approx 20 mV/div terminated into 1 MΩ.
Gate OutputsPositive gates from both time bases (approx 5 V)
Power RequirementsQuick-change line voltage selector provides six ranges; 110 V, 115 V, 120 V.  220 V, 230 V, and 240 V, each ± 10%.  48 to 440 Hz, 75 watts (465) or 100 watts (475, 475A) max at 115 V and 60 Hz.  Operation from 12 or 24 V dc is available with Option 07.
DimensionsCabinetRackmount
incmincm
Height (w/o pouch)6.215.77.017.7
Width (with handle)12.932.819.048.3
Depth (with panel cover)18.146.018.045.7
Depth (handle extended)20.351.6  
Weights (approx)lbkglbkg
Net (without panel cover)22.810.329.413.3
Net (with panel cover and accessories)25.311.5  
Shipping37.016.758.026.3



Количка  

Няма продукти

Доставка 0,00 лв
Сума 0,00 лв

Количка Поръчай

Нови продукти

  • Импулсно захранване MV18-Y120150-C5 18V/1A с букса 2.1x5.5x9mm
  • Импулсно захранване S06A13-120A050-P4 / SITECOM WLR-3100 12V/0.5A с букса 2.5x5.5mm
Импулсно захранване MV18-Y120150-C5 18V/1A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер MV18-Y120150-C5... >>
Импулсно захранване S06A13-120A050-P4 / SITECOM WLR-3100 12V/0.5A с букса 2.5x5.5mm
Импулсен захранващ адаптер  S06A13-120A050-P4 /... >>
Импулсно захранване HSWF120150E / CAP018121 12V/1.5A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер HSWF120150E /... >>
Импулсно захранване EGA-120140VE / 311P0W112 12V/1.4A с букса 2.5x5.5x9mm
Импулсен захранващ адаптер EGA-120140VE /... >>
Импулсно захранване AMS-1201000SV 12V/1A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер  AMS-1201000SV 12V... >>
Импулсно захранване SAG024F 3 12V/2A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер SAG024F 3 12V 2A с... >>
Импулсно захранване KSAS0181200150HE 311P0W128 12V/1.5A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер KSAS0181200150HE... >>
Импулсно захранване NBS36C120300HE 12V/3A с букса 2.5x5.5x9mm
Импулсен захранващ адаптер NBS36C120300HE 12V... >>
Импулсно захранване D-Link CF0605 5V/1.2A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер D-Link CF0605 5V... >>
Импулсно захранване SYS1428-1812-W2E 12V/1.5A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер SUNNY... >>
Импулсно захранване D-Link AMS47-050100FV 5V/1A с букса 2.1x5.5x9mm
Импулсен захранващ адаптер D-Link... >>
AP1345 активна цифрова ефирна антена- външна
AP1345 Активна външна ефирна логопериодична... >>
Термосвиваем шлаух 4.5mm черен
Термосвиваем шлаух 2:1; ф4.5mm; черен;... >>
LAN Patch кабел CAT6e UTP 10m RJ45-RJ45
LAN Patch кабел CAT6e UTP 10m RJ45-RJ45... >>
Кабел за автолампа H4
Порцеланов цокъл за автомобилна лампа тип H4 с... >>
ATF1508ASV
ATF 1508 ASV / EEPLD - Electronically Erasable... >>
UL1481
UL 1481 НЧУ IC: audio amplifier AF medium... >>
Оптична мишка USB 1600 dpi, FC-5082, черна
Оптична мишка USB 1600 dpi, FC-5082, черна... >>
кабел стерео жак 3.5мм (мъжки) - стерео жак 3.5мм (мъжки) 5м Cabletech eco-line
Кабел stereo Jack 3.5mm (мъжки) - stereo Jack... >>
кабел стерео жак 3.5мм (мъжки) - стерео жак 3.5мм (мъжки) 5м
Кабел stereo Jack 3.5mm (мъжки) - stereo Jack... >>

Всички нови продукти